No description
  • OpenSCAD 98.3%
  • Shell 1.7%
Find a file
2026-09-26 15:24:55 -05:00
.gitignore Add back hooks for hanging height adjustment 2026-09-26 15:24:55 -05:00
necklace_display.scad Add back hooks for hanging height adjustment 2026-09-26 15:24:55 -05:00
README.md Add back hooks for hanging height adjustment 2026-09-26 15:24:55 -05:00
render.sh Add back hooks for hanging height adjustment 2026-09-26 15:24:55 -05:00

Necklace display holder

A parametric OpenSCAD stand based on the reference photograph: a backward-leaning, flat display face with rounded-bottom necklace slots, two triangular rear braces, and a low base. The back is mostly hollow to avoid a heavy solid wedge. Rounded rear cleats let you take up spare chain to adjust the front hanging height. Necklaces are not included in the model.

Open necklace_display.scad in OpenSCAD. Edit the variables at the top, or use the Customizer; press F5 to preview and F6 to render before exporting an STL. All dimensions are in millimeters.

Main dimensions

Variable Default Meaning
panel_width 200 Width of the display face
panel_height 220 Height measured along the face
panel_thickness 4 Thickness perpendicular to the face
lean_angle 12° Backward tilt from vertical
slot_count 10 Number of top slots; allows five two-slot necklace positions
slot_pitch 20 Center-to-center distance between slots
slot_width 5 Slot opening width
slot_depth 6 Depth measured down from the top edge
slot_edge_margin (computed) 10 Side edge to outermost slot center; slots are automatically centered
base_depth 90 Rearward depth from the panel's bottom rear edge
base_thickness 3 Bottom plate thickness
support_thickness 5 Thickness of each triangular brace
support_side_inset 0 Side edge to outside face of each brace; zero makes the braces flush with the panel sides
support_height_ratio 0.5 Fraction of panel height reached by the braces (110 mm by default)

Slot pitch is specified directly. Edge margins are computed as (panel_width - (slot_count - 1) * slot_pitch) / 2 to center the slots. Increase panel width if adding more slots; assertions reject slots that do not fit. With the default 5 mm slot width, interior teeth are 15 mm wide. Dimensions are estimates, not measurements from the photograph. The default overall envelope is approximately 200 × 94 × 216 mm.

Rear chain adjustment

There is one cleat column between every adjacent pair of top slots: ten slots give nine columns, not five. Each column has three cleats by default (27 total), centered 30, 65, and 100 mm down from the top. Adjacent positions share slots; nine columns provide placement choices, not nine independent two-slot necklace positions.

Route the necklace through two neighboring slots and catch its rear loop around a cleat between them. A lower cleat takes up more chain behind the panel and raises the necklace at the front. The small tip bends toward the panel bottom to retain the loop as it is pulled toward the top slots. These are open cleats, not locking clips.

Variable Default Meaning
rear_cleats_enabled true Include rear chain cleats
cleat_rows 3 Cleats per column
cleat_top_offset 30 Top edge to first cleat center along the face
cleat_row_spacing 35 Vertical center spacing along the face
cleat_width 10 Cleat width across the face
cleat_height 4 Stem height along the face
cleat_projection 8 Total distance projecting from the back
cleat_lip 2 Downward tip offset and ramp depth (45° slope)
cleat_corner_radius 1 Radius of the rounded footprint corners

Printing

The stand is modeled as one connected solid with its base on Z=0, not in print orientation. For front-face-down printing, use your slicer's lay-on-face tool to put the broad front face flat on the bed. The rear cleats then grow out of the panel: a straight stem followed by a gently sloped tip, rather than an abrupt overhanging cap. They are designed to print without supports in this orientation; confirm the 45° slopes work with your printer and settings.

Check the existing base and braces separately for overhang support and bed fit in the slicer. Remove any rough edges or stringing before placing delicate chains on the cleats. Stability also depends on necklace weight—adjust base depth as needed.

Command-line STL export

openscad -o necklace_display.stl necklace_display.scad

Example with a wider face and more slots:

openscad -o necklace_display_wide.stl \
  -D 'panel_width=240' -D 'slot_count=12' necklace_display.scad